← Library

It Always Ran Like That

Reading a PID

Pia stood at the door of Aunt Dagmar's office, her backpack still on her shoulders. The Schematic Wall glowed under the fluorescent lights—page after page of laminated drawings, covered in lines and circles and tiny symbols.

"Ready for something new today?" Aunt Dagmar asked, looking up from her desk.

Pia nodded. "Are we going to find another Difference?"

"Not exactly." Dagmar pulled a rolled-up paper from a tube on her desk. "Today, I want to teach you how to read a P&ID properly. Not just look at it—actually read it like a map."

She unrolled the paper across her desk. Pia leaned in.

The drawing was a tangle of lines going every direction. Some lines were solid. Some were dashed. Some had arrows. Small circles sat along the lines like beads on a string, each with letters and numbers inside.

"This is a Piping and Instrumentation Diagram," Dagmar said. "It shows how a piece of plant is supposed to be built. Every pipe, every valve, every instrument. See these circles?"

Pia pointed to one. "What's inside it?"

"That's an instrument. The letters tell you what it does. F-I-C means Flow Indicator Controller. It measures the flow and controls it."

Pia's eyes moved across the drawing. "And these lines?"

"Those are pipes." Dagmar traced one with her finger. "Different line styles mean different contents. Solid lines are process fluids. Dashed lines are electrical signals. Dotted lines are pneumatic—air pressure."

Pia studied the drawing for a long moment. Then she looked up. "Where's the real plant?"

Dagmar smiled. "That's exactly the right question."


They walked out onto the plant floor. The air smelled like metal and oil. Pipes ran overhead in every direction, and Pia could hear the hiss of compressed air and the rumble of pumps.

Dagmar stopped in front of a section of pipework. It was about as long as three cars, with several branches and valves along its length. She handed Pia the rolled-up drawing.

"Here's your section," Dagmar said. "And here's the real thing. I want you to walk through and find where the drawing matches the plant. Find me three things that match, and one thing you're not sure about."

Pia took the drawing carefully. She unrolled it and looked at the symbols at the start of the line.

"Okay," she said. "Here goes."

She walked to the left end of the pipe section. On the drawing, there was a big circle with a cross through it—a valve symbol she recognized. "This is a gate valve," she said, pointing to the real pipe. "There it is."

Dagmar nodded. "Match number one."

Pia moved a few steps along. The drawing showed a smaller circle with an L-shaped symbol inside. "This is a check valve," Pia said. "It only lets flow go one way."

She found it on the real pipe. "There. Same shape, same direction."

"Match number two," Dagmar said.

Pia studied the drawing again. Near the middle, there was a dashed line going from a small circle to a larger box. The circle had a label: PI, for Pressure Indicator.

"This one connects to a pressure gauge," Pia said. She looked up at the real pipe. "And there's the gauge." It was a round dial with a glass face, mounted on a bracket. "The dashed line means it reads the pressure but doesn't control anything."

"Very good. Match number three."

Pia continued along the pipe. The drawing showed another valve near the end—this one was a triangle with a line through it. She stopped. She looked at the drawing. She looked at the real pipe.

A valve was there, but it was different. The symbol on the drawing was a control valve—one that opened and closed automatically, based on signals from an instrument. The valve on the real pipe was bolted to a manual wheel, with no wires or air lines connected to it.

"Hmm," Pia said.

"What do you see?" Dagmar asked.

"There's supposed to be a control valve here," Pia said slowly. "But the valve in the real plant is manual. You have to turn the wheel by hand." She looked up. "It's not the same kind of valve."

Dagmar came over and looked at the drawing, then at the pipe. "You're right. They don't match."

"So which one is wrong?" Pia asked.

"That's what we're going to find out."


Back in Dagmar's office, they laid the drawing on the desk. Dagmar found another document in her filing cabinet—a spec sheet, covered in numbers and notes.

"This is the original specification for that section," Dagmar said. "It describes what equipment was supposed to be installed."

She ran her finger down the page. "Here. Line 47-B. 'Control valve, 2-inch, pneumatically actuated.' That matches the drawing."

Then she flipped to a maintenance record. "And here's the work order from ten years ago. Someone replaced the control valve with a manual valve during a shutdown. They never updated the drawing."

Pia frowned. "So the drawing is right, and the real plant is wrong?"

"Only in one way," Dagmar said. "The drawing shows what it's supposed to be. The real plant is what it became because someone made a change and didn't document it."

She pulled the drawing to her side of the desk. "The problem is, now when someone reads this P&ID, they think there's a control valve here. If they need to control the flow automatically, they'll look at the drawing, see the valve, and assume it's working."

"But it's not even there," Pia said.

"Exactly. And the only way to find that out is to compare the drawing to the real thing."

Pia looked at the drawing again. She thought about the three matches and the one difference.

"So the differences are like clues," she said.

"Differences are always clues," Dagmar said. "They tell you where to look. That's what the Schematic Wall is for. That's why we always start with the document."

Pia picked up the drawing and rolled it carefully. "Can we make a new drawing? One that shows the manual valve?"

Dagmar smiled. "That's called an 'as-built' drawing. It shows how the plant is actually built, not how it was originally designed. It's important to keep those updated, too."

"Because otherwise the next person will be confused," Pia said.

"Or worse," Dagmar said. "They'll trust the drawing and make a decision based on something that isn't there."

Pia looked at the Schematic Wall. "So the P&ID tells you what's supposed to be there. The real plant tells you what's actually there. And your job is to find where they're different."

"Now you've got it," Dagmar said.

Pia pulled out her notebook and opened it to a fresh page. At the top, she wrote:

The Differences List

Then she wrote:

Section 47-B: Drawing shows control valve. Real plant has manual valve. Drawing is right; plant was changed. Need to update drawing.

She looked up at the wall of schematics. "Aunt Dagmar?"

"Yes?"

"When we fix the drawing," Pia said, "does the real plant need to match it again? Or do we just fix the paper?"

"Great question." Dagmar leaned back in her chair. "The real plant is working fine with the manual valve. It does the job—just not automatically. So the right fix is to update the drawing to show what's actually there."

"And if the real plant wasn't working fine?"

"Then we might fix the plant to match the drawing. That's the other option. Either way, the drawing and the real thing have to agree. When they don't, someone has to decide which one is right for the job."

Pia looked at her notebook. She had four items on her list: three matches and one Difference. The matches told her the drawing was mostly right. The Difference told her where to dig deeper.

"Find the schematic first," Pia said quietly. "Then look at the real thing. Find where they're different. That's where the problem is."

Dagmar smiled. "You're ready for the next one."

Pia closed her notebook. "What's next?"

Dagmar reached across her desk and picked up a phone. "Let me call Harold. He mentioned something about a valve that's been leaking for years. He says it always ran like that."

Pia grinned.

"That sounds like a Difference," she said.

"Let's go find out."