← Library

The Three Man Job

The Job Oona Planned

Pete came into the break room with a piece of paper. The paper had a drawing on it, and the drawing looked like a tube with two smaller tubes on either side. He put it on the table.

"We need to replace the coupling on the Number Two Strander," Pete said. "It's a routine job, but it's tricky. The shaft has to be perfectly aligned, and the coupler has to be torqued in a specific sequence."

Oona looked at the drawing. She had seen couplings before. They connected motors to pumps, or motors to conveyors. This one connected the big strander motor to the spinning drum that made the whole building shake.

"How long do you think it'll take?" Pete asked Lars.

Lars took a sip of his coffee. "Oona's going to plan it."

Pete looked at Oona. Then he looked back at Lars. "Lars, are you sure she should—"

"Let her plan it," Lars said.

Pete held up his hands. "She's going to make mistakes."

Lars nodded. "That's the job."

Oona felt her stomach do a little flip. She had helped on jobs before. She had fetched tools, brought water, held the flashlight, and asked lots of questions. But she had never planned a job. Not a whole job.

"Uncle Lars," she said, "what if I plan it wrong?"

"Then you'll know for next time," Lars said.

"That's not reassuring."

"No," Lars said. "But it's true."


Oona got a piece of paper from the office and a pencil from behind the coffee machine. She sat at the table where Pete had spread his drawing.

The job was a routine coupling job. That meant the strander motor had to be disconnected from the drum so the old coupling could be taken off and a new one put on.

Oona thought about the steps. She had watched Lars do this before, on the old conveyor out back.

First, you lock out the power. That was always first. You can't disconnect anything if it might turn on while you're working on it. Lars called it "the only rule that matters."

Second, you put a sling around the motor and hook it to the crane. There is one crane in the Strathmore Mill, and everybody always forgets this until they need it. Oona wrote "BOOK THE CRANE" in big letters at the top of her paper, right next to "LOCKOUT."

Third, you loosen the bolts. Not all the way—just enough to break the tension. Then you use the jacking bolts to separate the motor from the drum. Then, with the crane, you lift the motor just a little—a quarter of an inch, barely enough to see light under it—and you pull it back.

Fourth, you take off the old coupling. Fifth, you put on the new one. Sixth—and Oona knew this was the part Pete always wanted to rush through—you re-align the shafts. If the motor and the drum aren't perfectly lined up, the new coupling will wear out in a week. The shaft has to be true.

But how did you check the alignment? Lars had shown her once, with the dial indicator. He had clamped the little tool to one shaft, put the needle against the other shaft, and turned the shaft slowly. If the needle moved, the shafts were out of alignment. If it didn't move, they were true.

Oona wrote all of this down. She made a list of tools: wrenches, jacking bolts, sling, dial indicator, torque wrench, and the new coupling, which Pete said was already in the storeroom.

She looked at her paper. The steps were all there, in order. She had put the lockout first and the crane booking second.

But something felt wrong.

She looked again at Pete's drawing. The coupling on the drawing had a note in the corner: "TORQUE TO SPEC—SEE MANUFACTURER'S MANUAL."

Oona went to the office and found the manual. The manual was big and dusty. She opened it to the section on couplings.

There it was. The torque sequence. You don't just tighten all the bolts in a circle. You tighten one, then the one across from it, then the one next to that, then the one across from that. In a star pattern. If you tightened them in a circle, the coupling would bend slightly. It wouldn't be true.

Oona added that to her list: "Torque in star pattern, per manual."

She showed the paper to Lars.

Lars read it. He read it slowly, from top to bottom. Then he looked at the drawing. Then he looked back at the paper.

"That's the one," he said.

"Really?" Oona said.

"Really. You booked the crane. You locked out the power. You checked the star pattern. That's the job."

He handed the paper back. "Now let's do it."


Pete showed up when they were lifting the motor. He looked at the crane, at the sling, at the coupling already on the table, at the torque wrench laid out neat and ready.

"You got the new coupling from the storeroom already?" he said.

"Oona planned it," Lars said.

Pete looked at the plan. He read the steps. He nodded. "This is good," he said. "This is really good."

The lockout was already done. The crane was already booked. The motor came off clean. The old coupling came off in two pieces, just like it was supposed to.

Oona checked the new coupling. She cleaned the shaft with a rag, the way Lars had taught her. She put the new coupling on, and Lars helped her bolt it down—one bolt, then the one across from it, then the next, then the one across from that.

Lars checked the alignment with the dial indicator. He turned the shaft slowly. The needle didn't move.

"Right," he said. "That's it."

The job took four hours. Pete had guessed it would take two days.


That night, Oona wrote in the millwright's notebook. She wrote in her careful, large handwriting:

You learn to plan by planning. The plan you're afraid of is the plan worth doing.

Lars read it. He read it slowly. Then he nodded and said, "That's the one."