← Library

The Three Man Job

The Bolt That Kept Coming Back

"Lars," Pete said, holding up a small piece of metal. "This bolt keeps coming loose on Number Four conveyor. Third time in two months. We keep tightening it, and it keeps coming back out."

Uncle Lars looked at the bolt. Then he looked at Pete. Then he looked at the bolt again.

"Where exactly?" Lars asked.

"Same spot every time," Pete said. "About halfway down the conveyor. We've tightened it three times. I'm thinking we need to weld it in place."

"Let me look at it first," Lars said.

Oona followed Uncle Lars through the big noisy building. The Strathmore Mill hummed and clanked and rumbled all around them. They walked past the big Stranders, past the Press, past the crane that everyone always forgot about until they needed it.

They stopped at Number Four conveyor. A long belt of rubber and metal rollers, carrying wood chips from one end of the mill to the other.

Lars stood and looked. He didn't touch anything. He just watched.

The conveyor moved. The belt rolled. The rollers turned.

Somewhere, halfway down, a bolt sat in its hole.

"Show me the spot," Lars said.

Pete pointed to a bolt on the side of the conveyor frame. It looked like every other bolt on the machine. Same size. Same shape. Same silver color.

Oona leaned in close. "It doesn't look any different from the others."

"No," Lars said. "It doesn't."

"So why does it keep coming loose?" Oona asked.

Lars didn't answer. He was watching the conveyor move.

He watched for a long time.

Then he walked down the line of rollers, past the loose bolt, past the next one, past the next one after that. He stopped at a section about twenty feet down.

He knelt down. His knees made a small sound, but he didn't say anything about it.

"Oona," he said. "Come here."

Oona came over and knelt beside him.

"Watch this sprocket," he said.

Oona watched. The sprocket was a wheel with teeth, turning a chain that moved the conveyor. It was turning exactly the way it was supposed to turn.

Except.

"There," Lars said. "See it?"

Oona looked. She saw the sprocket turn. She saw the chain move.

She saw it again.

The sprocket was wobbling. Just a little. Just barely. But it was wobbling.

"Worn teeth on one side," Lars said. "Every time it turns, it makes a little shake. Not big enough to feel. Just big enough to travel down the frame."

"Travel down the frame," Oona repeated. "What happens when it gets to the bolt?"

"It vibrates it loose," Lars said. "Slowly. Over weeks. You tighten it, and the sprocket keeps wobbling, and the shake keeps traveling, and the bolt works its way back out."

Pete had walked up behind them. "So what do we do? Tighten it tighter?"

"That's not fixing it," Lars said.

"It's tight now," Pete said.

"Until next week," Lars said.

He stood up. He brushed off his knees.

"We need a new sprocket," he said. "One section down. That's the problem."

Pete looked at the sprocket. It looked fine. It looked like it had years left in it.

"Are you sure?" Pete asked.

"I'm sure," Lars said.


Two hours later, the new sprocket was in. The old one came off with a wrench and a pry bar and some grunting from Lars, who said the word "tricky" once and then didn't say anything else.

The new sprocket went on. It sat straight. It turned true.

Lars walked back to the loose bolt. He didn't tighten it. He just touched it with his fingers.

It was still loose.

"Now we tighten it," he said.

Oona handed him the wrench.

Later, after the conveyor was running again and the bolt was snug in its hole, Oona sat in the corner of the millwright shop with Uncle Lars's notebook open on her lap.

Uncle Lars was washing his hands at the sink. He didn't watch her write. He never watched. But he always read what she wrote.

Oona wrote:

A bolt that keeps coming loose is a symptom. Find the cause.

She slid the notebook across the bench.

Uncle Lars dried his hands. He walked over. He picked up the notebook.

He read the line.

He nodded.

"That's the one," he said.